Where is the subnet mask on my router

Now lets look at why we subnet with different size masks. On the router we have got with 150.150.0.1 on fastethernet 0/0 and 150.150.1.1 on fastethernet 0/1 lets assume that we have a serial interface. What shall we do with addressing on the serial interface? If we use the same mask we can put address 150.150.2.1 on the serial.

Aug 04, 2015 · When you connect to a LAN (Local Area Network), the router will assign your computer an IP Address, Subnet Mask, Gateway, and DNS Server(s) IP Address = the unique address of your computer on the LAN. Subnet Mask = Determines what segments of your Network ID your computer can communicate with. Gateway = Usually your router. Your router is the Nov 09, 2018 · In the IP Subnet Mask, type the subnet mask of the router. The IP address and subnet mask identifies which addresses are local to a specific device and which must be reached through a gateway or router. 7. Change the RIP settings. Router Information Protocol (RIP) allows a router to exchange routing information with other routers. a. Jan 15, 2011 · What it form of feels which you're attempting to try this's - to establish STATIC IP ADDRESSES on the two desktops once you pass to run, then kind cmd {enter} and then ipconfig {enter} write down the IP handle, Subnet mask and Default Gateway you will possibly try this by going to regulate PANEL go with community Connections ideal click on the interior of reach section Connection which you I'm wondering if a subnet mask will do the trick. I (sort of) understand that subnet masks are a way of telling the network section of an IP address from the host part, and I think that means I can limit the number of possible addresses, and therefore users, on the router. Here you need to verify if the problem is the subnet mask or the IP included under the interface, in this case as the subnet mask is /24 you need to include a valid IP different with ending "0" or "255". Under the interface you can configure valid IP addresses only. Network: 192.168.1.0/24 Valid IP addresses: 192.168.1.1 to 192.168.1.254

For subnetting to work, the router must be told which portion of the host ID should be used for the subnet network ID. This little sleight of hand is accomplished by using another 32-bit number, known as a subnet mask. Those IP address bits that represent the network ID are represented by a 1 in … Feb 10, 2015 · Aside from what others have said about the new subnet mask. 1. double check every switch, router, firewall (nat translations, routng rules, interface/port definitions), server, printer, or device that has a static IP address prior to making the change, identifying each device that will need to have their subnet changed. Hello everybody. I have set my router on a subnet. Cause I use static IP's on my 2 main pcs and one server I still have available 2 IPs. These I want the BT HomeHub to distribuit, by ways of DHCP, whenever requested. The problem is that I now have seen that the router wont accept it and says "In

Jan 15, 2011 · What it form of feels which you're attempting to try this's - to establish STATIC IP ADDRESSES on the two desktops once you pass to run, then kind cmd {enter} and then ipconfig {enter} write down the IP handle, Subnet mask and Default Gateway you will possibly try this by going to regulate PANEL go with community Connections ideal click on the interior of reach section Connection which you

If your DHCP subnet mask on the Actiontec is not /25, then this is seriously messed up. spacedebris wrote: the IP addresses 192.168.1.100-150 are in a special range on the Verizon router reserved for STB's. Jan 13, 2012 · Depends on the subnets: 3 class c networks for example. 192.168.0.0/24. 192.168.1.0/24. 192.168.2.0/24. The subnets above have 3 different gateways, if you combine them the user devices having the wrong gateway addresses would stop communicating so you would need to adjust that. You cannot change the subnet mask to 255.255.0.0 in the WRT600N. You will need to leave your LAN subnet mask set to 255.255.255.0 in both routers. To make your system work, you need to convert your WRT600N to a WAP (wireless access point). Apr 03, 2012 · As shown in the screen shot above, I have my router settings set for a subnet mask of 255.255.255.0 and DHCP Range of 192.168.1.100 - 192.168.1.149 which is default I believe, I haven't changed either setting the only thing I changed is in the Port Range Forward to open ports for my Xbox 360's static IP which I've set to "192.168.1.2" out of my